Once I finished the clown fish, a.k.a Nemo, I found that there was a similar modular version of Nemo's friend - Dory, who is a Blue Tang. So I ended up making this one too. This model is even easier to do than Nemo, because of the bigger size of this fish.

Similar to the clown fish, this one is also not a pure origami model, since it involves gluing of the pieces. And this one is also made from 4 different sized squares, albeit different colours - 2 of the squares are yellow, one blue and one black, since these are the colours of the blue tang fish. This model is also created by Mariko Miyamoto of Oriart.

While each module is folded from a square, the size of the square varies.  So the body is made from a blue 15 cm square, the black section is made from black 10 cm square, the little yellow fin between the black and blue sections is made from a yellow square of 3.75 cms and finally, the tail is made from a yellow square, 7.5 cms side. The different modules are held together by glue or tape.

So, have a go at it. It is a fun model and is sure to attract a young audience!

Model Details:

Model: Blue Tang 

Creator: Mariko Miyamoto

Difficulty Level: Low Intermediate

Paper Ratio: Square

Paper Size: Blue 15 cm square | Black 10 cm square | Yellow 3.75 cm square | Yellow 7.5 cm square

Model Size: ~5 inches across

Tutorial: Youtube Part 1 and Part 2

I am sure most of us have watched the animated movie "Finding Nemo". I have watched this movie, repeatedly, because Little Miss loves it! So naturally, when I came across this youtube tutorial to fold a two-dimensional clown fish, I couldn't resist folding it!

The fish is not a pure origami model, since it involves gluing of the pieces but I guess we could say that it is a modular one, made from 4 modules - a tail, a body, the head and the fins and is created by Mariko Miyamoto of Oriart.

While each module is folded from a square, the size of the square varies.  So the tail is made from a 5 cm square, the body from a 10 cm square, the fins from 7 cm square and the head from 5 cm square. Obviously the model works best with a rich orange single-sided paper ie., paper that is orange on one side and white on the other. The different modules are held together by glue or tape.

The sizes I have mentioned, give a clown fish that is the bigger of the two in the picture. I named this one Marlin 😀 And naturally, Little Miss wanted a smaller version, for Nemo. So I halved all the values from the previous model to end up with a mini clown fish - Nemo. Though the squares were small, since the model was fairly easy, I was able to make the smaller fish without any trouble.

So, have a go at it. It is a fun model and is sure to attract a young audience! And the lovely alternating colours adds a whole lot of beauty to the characters.

Model Details:

Model: Clown Fish 

Creator: Mariko Miyamoto

Difficulty Level: Low Intermediate

Paper Ratio: Square

Paper Size: 2 squares of 5 cm (2 inches), 1 square each of 10 cm (4 inches) and 7 cm (2.7 inches) for the bigger fish
2 squares of 2.5 cm (1 inch), 1 square each of 5 cm (2 inches) and 3.5 cm (1.3 inches) for the smaller fish

Model Size: ~3 inches across (bigger fish) and ~2.5 inches across (smaller fish)

Tutorial: Youtube

These little Easter baskets were made from some left-over tubes that were lying around. They were pretty easy to make and quick work too..

Of course, they don't serve any purpose given their size 😄 But are super cute to look at, so may be I will end up making more of these!!

Model Details:

Model: Easter Basket

Difficulty Level: High Intermediate

Tutorial (making newspaper tubes): Youtube

Tutorial (making the basket): Youtube