Before trying the Ninja Star Modular Cube, I tried out one last cube. This is again from the book 'Modular Origami Polyhedra'. As before, this is from the chapter on Decoration Box System. Almost all the cubes have the same heading, namely, 'Modular Cube', so I am also using the same name :) To be more specific, this is the 8th cube in this chapter. The design is by Lewis Simon.

When I looked at this model, I liked the shape which is different from the usual cube shape. This looks a little like the last modular cube I did, but with more pronounced truncated corners. Assembling the model is different from usual for me. An interesting model to fold :)

Model Details:

Model: Modular Cube 

Creator: Lewis Simon

Book: Modular Origami Polyhedra
 
Author: Lewis Simon, Bennett Arnstein, Rona Gurkewitz
 
Difficulty Level: Low Intermediate

Paper Ratio: Square

Paper Size: 3 inches

Model Size: Square cube with approximate side of 2.25 inches

Modules: 12

Since making my last cube, I have made a few more cubes from 12 sheets of paper. All are from the book 'Modular Origami Polyhedra' . This one is a Sonobe Cube formed from Decoration Box modules. We start off folding as for the decoration box module and then add a few more folds to get the final module.

I first tried this model from 2-inch squares. Quite a tough job!! Folding these thin creases are quite painful, but not as painful as creasing paper that has already been folded 4-5 times!! My thumb took quite a beating! I would strongly advice a bone-folder for this model. Unfortunately, I don't have one, so had to make do with my poor thumb :(

Model Details:

Model: Sonobe Cube from Decoration Box Modules 

Creator: Lewis Simon

Book: Modular Origami Polyhedra
 
Author: Lewis Simon, Bennett Arnstein, Rona Gurkewitz
 
Difficulty Level: High Intermediate

Paper Ratio: Square

Paper Size: 2 inches

Model Size: Square cube with approximate side of 1.25 inches

Modules: 12

As I had mentioned in my previous post, I tried out the modular cube variation, this one in orange. The assembly is the same as the modular cube. The only change, in fact, is the way the initial fold is done, so that the reverse of the paper becomes visible. So it is a good idea to use paper coloured on both sides, in contrasting colours. I preferred using single-sided orange coloured paper. I think it has turned out quite well :)

But in reality, folding the modules turned out to be an unexpected challenge! I had used the same paper size as in my previous cube (1.25 by 3.5 inches). Unfortunately, this model had a couple of additional folds, resulting in really thin strips. And folding those thin strips in such a small paper turned out to be painful!! I used a ruler to ensure that I got the folds right. Thankfully the paper was quite strong, I am sure I would have ended up tearing quite a few modules otherwise!

Model Details:

Model: Modular Box Variation 

Creator: Bennett Arnstein

Book: Modular Origami Polyhedra
 
Author: Lewis Simon, Bennett Arnstein, Rona Gurkewitz
 
Difficulty Level: Low Intermediate

Paper Ratio: Rectangle in ratio 1:2

Paper Size: 1.25 by 3.5 inches

Model Size: Square cube with approximate side of 1.25 inches

Modules: 12

The decoration and modular boxes from the book 'Modular Origami Polyhedra' are beautiful and very tempting! The boxes are all cubes made from 12 modular units. They are quite easy to make as well. And I love the little windows in the cubes.

I had previously tried out the original decoration box and was quite pleased with the results. This time, I tried out the first of the modular cubes, which is actually a variation of Lewis Simon's decoration box.

This turns out to be much more economical than the decoration box too, since it is made from 12 rectangles in 1:2 ratio (a square cut in two). The decoration box, on the other hand, is made from squares. So you can make 2 of these modular cubes for each of the decoration boxes :) Naturally, the size of the cube is also smaller than the decoration box.

While folding the cubes, the one issue I faced was that, the backside of the paper (white in my case), can be seen peeking out in quite a few places! No matter how I folded it, the white was visible :( I guess paper coloured the same on both sides would have been better.

Well, I will be folding a few more of these cubes. The next variation of the decoration box is the next on my list, followed probably by the Ninja Star cube.

Model Details:

Model: Modular Box 

Creator: Bennett Arnstein

Book: Modular Origami Polyhedra
 
Author: Lewis Simon, Bennett Arnstein, Rona Gurkewitz
 
Difficulty Level: Low Intermediate

Paper Ratio: Rectangle in ratio 1:2

Paper Size: 1.25 by 3.5 inches

Model Size: Square cube with approximate side of 1.25 inches

Modules: 12